Browse Categories
Browse by Manufacturer

Walco F110E Series Friction Feeder

This feeder is Built to Last! Made in the USA with high quality components that will last a lifetime! 1 YEAR WARRANTY!

Part Number # : F110E
Manufacturer: Walco
MPN:: F110E Series
the high capacity use demanded by today's commercial environment.


  • Quick and Easy Setup
  • Variable Speed
  • Independently Adjustable Belts & Separator            
  • Dual Durometer Separator
  • Adjustable Exposure Table
  • Simple Under 5 Min. Belt Replacement
  • Feeds Wide Variety of Products
  • High Capacity Feed Hopper
  • Heavy Gauge Steel Construction
  • Rotatable Separator
  • Sealed Shaft Locking Collar Bearings
  • Magnetic Rear Adjustable Roller Wedge
  • 1 Year Warranty


Articulating Acceleration Assembly 
Pulls a separation between pieces before
leaving the feeder.
Remote Speed POT
Feeder Speed control POT located on a Walco
transports base, allows feeder speed control
from the same location as transport base and
conveyor speed.

Speed Following

Allows Walco Systems feeders to follow
transports base belt speeds, using one speed control.


Material Size: Min. 2"W x 4"L - Max. 11"W x 18"L
Material Thickness: 1.125" Max (Standard)
Electrical: 110 VAC 1-Phase 5 Amp Circuit
Interlock: Dry Contact (Low Volt) Standard
Physical: 18.1"L x 15.0W x 21.25"H

Overview of the Feeder

Feed belts can be replaced in 10 minutes! 

Walco F110E Series Friction Feeder
Walco F110E Series Friction FeederOversized Bearings and Shafts means the Walco F110E may never break down!  And is why we can offer a 1 year waranty!The separator on the Walco F110E has a High Friction Black side and a low friction blue sideWalco F110E shown with maximum belt exposure Walco F110E shown with 1/2 belt exposure


Extended Table
Your Price: $4,065.00
<< Previous in News & Specials Next in News & Specials >>

Product Reviews

(4 Ratings, 4 Reviews) Average Rating:
So much better! They pay for themselves
John, L (PA) 1/28/2021 12:40 PM
It's been 4 years now. On our last feeder we would need to replace shafts and bearings about once a year. Belts about once every other month and the separator about once a month. After 4 years, we went through 1 set of belts and 2 sets of separators. We now have 3 and plan on getting 2 more to replace the last 2 money pit feeders
Built Tough!
Stephen W (NC) 7/10/2018 11:08 AM
This is how a feeder should be built. We haven't replaced a single bearing or shaft. In the same timeframe, we've rebuild our S############## 3 times and our S########### 4 times. We could have purchased 2 more F110E for what we spent on the S############## or the S###########. Not to mention the downtime. I showed the invoices to the owner on a Friday, and the production manager quit on Monday. Guess who is the new production manager! I feel bad for him, but this is just a sample of the bad decisions he made. Like recently purchasing a used Secap Jet1. Turns out, it's no longer supported so we can't get parts
The F110E is a Beast!
Marc (PA) 9/1/2016 4:25 PM
We've had the F110E friction feeder for 2.5 years now. We have a SureFeed, Straight Shooter and a StreamFeeder. The Walco not only feeds better, it's a lot more durable! We haven't changed a single part on it yet! The other feeders would need belts and separators and far too often, bearings and shafts. Saving up for the Walco VF200 vacuum feeder.
Built like a tank!
Bill M (Bensalem, PA) 4/21/2014 1:48 PM
We have a Surefeed feed, a Stream Feed, and a Straight Shooter. Thank you Walco for finally getting it right! They guys actually fight over who is going to get the F110 to run their job with. So we will be buying another one or 2 as soon as the others throw another bearing. I've had it with buying bearings and shafts for the other feeders! Never again! The Walco sets up easy and feeds a lot more consistently.
Shopping Cart
Your cart is empty.
​​All For Mailers & Supplies For Mailers BBB Business Review
Proud Veteran Owned Business Member!
Mailing Lists

Original text